News Center
We are dedicated to providing users with cost-effective instruments and meticulous services! Welcome to visit, guide, and negotiate business with us.
Current Position:
Home > News > Company News

Why Does a Vortex Flow Meter Stop Reading at Low Flow Rates? 3 Common Causes and How to Troubleshoot Them

2026-11-16

1. A Common Field Problem


At a chemical plant, a DN80 vortex flow meter installed on a circulating water pipeline worked normally during the day under full-load conditions. However, when the plant load dropped to approximately 30% at night, the flow reading suddenly fell to zero, and the meter stopped generating pulse signals.


The operators initially suspected a faulty meter and replaced it with a new one. However, the problem remained unchanged.


After a 30-minute on-site inspection, the manufacturer's technicians identified the real issue: the nighttime flow rate had fallen below the meter's measurable range.


This is a common problem in industrial flow measurement. When a vortex flow meter stops displaying readings at low flow rates, the cause is not necessarily a meter failure. The actual operating conditions, transmitter settings, and installation environment should all be checked.


2. Three Main Reasons for Low-Flow Measurement Problems


1. The Flow Rate Is Below the Meter's Operating Range


A vortex flow meter works by detecting vortices generated alternately behind a bluff body, known as a Kármán vortex street. The vortex shedding frequency is proportional to the fluid velocity.


However, stable vortex shedding requires a sufficiently high Reynolds number. When the Reynolds number drops below approximately 2 × 10⁴, vortex shedding may become unstable and the signal amplitude can decrease significantly.


For many liquid vortex flow meters, the minimum measurable velocity specified in product datasheets is typically around 0.3–0.5 m/s.


When the actual flow velocity falls below this range, the vortex signal may become too weak for reliable detection. Even if the meter itself is functioning properly, it may no longer produce a valid output signal.


2. Low-Flow Cutoff and Filtering Settings Suppress the Signal


The transmitter's configuration can also affect low-flow measurement.


Three settings deserve particular attention:
 

  • Low-flow cutoff: If the cutoff is set to 5% of full scale (FS), any flow signal below this threshold may be forced to zero.

  • Signal filtering: Excessive filtering may suppress weak but valid vortex signals along with unwanted noise.

  • Signal gain: An unsuitable gain setting may prevent the transmitter from detecting weak signals at low flow rates.


These parameters are usually accessible through the transmitter's configuration menu. Incorrect settings can make a normally functioning vortex flow meter appear to have stopped measuring.


3. Installation Conditions and Fluid Properties Reduce the Signal-to-Noise Ratio


At low flow rates, the vortex signal is already relatively weak. Poor installation conditions can further reduce measurement reliability.


Common factors include:
 

  • Pipeline vibration: Mechanical vibration from pumps, supports, or nearby equipment can introduce interference.

  • Partially filled pipes: For liquid applications, an incompletely filled pipeline can cause unstable measurement conditions.

  • Liquid droplets in gas: Moisture or liquid carryover can interfere with gas flow measurement.

  • Partially closed upstream valves: Improper valve positioning can create turbulence and unstable flow profiles.


These conditions increase signal interference and may overwhelm the weak vortex signal, causing unstable readings or zero output.


3. Recommended Troubleshooting Sequence


Step 1: Check the Actual Operating Point


Calculate the flow rate and fluid velocity under both normal and minimum-load operating conditions. Then compare these values with the minimum measurable velocity specified in the flow meter's datasheet.


As a general reference:
 

  • Liquid applications: approximately 0.3–0.5 m/s minimum velocity.

  • Gas applications: approximately 3–5 m/s minimum velocity.


These are typical reference values, not universal limits. The actual minimum velocity depends on the meter design, size, fluid properties, and operating conditions.


If the actual velocity is consistently below the meter's operating range, consider reducing the meter size or selecting a different measurement technology, such as an electromagnetic flow meter, mass flow meter, or thermal mass flow meter.


When selecting a smaller meter, make sure the normal operating flow rate still falls within the middle portion of its measuring range.


Step 2: Check Low-Flow Cutoff and Filtering Parameters


Enter the transmitter configuration menu and inspect the following settings:
 

  • Low-flow cutoff: Commonly set between 1% and 5% FS. Depending on the process requirements, a trial adjustment to 0.5%–1% may be appropriate.

  • Signal filtering: Check whether the filtering strength is excessively high.

  • Signal gain: Verify that the gain is suitable for detecting weak vortex signals.


Record the original settings and measurement data before making adjustments. Compare the readings before and after each change to ensure that reducing the cutoff or filtering does not introduce excessive noise or unstable output.


Step 3: Inspect Installation Conditions and the Signal Transmission Chain


Check the following installation details:
 

  • Straight pipe requirements: A typical reference is 10D–15D upstream and 5D downstream, where D is the pipe diameter. Actual requirements depend on the meter design and upstream flow disturbances.

  • Flange alignment: Ensure that the meter is properly aligned with the pipeline to avoid installation stress and flow disturbances.

  • Grounding and shielding: Use a dedicated grounding arrangement where required, and ground the cable shield at one end according to the manufacturer's wiring instructions.

  • Vibration sources: Avoid installation near pump outlets and other sources of strong mechanical vibration.

  • Full-pipe conditions: For liquid applications, ensure that the pipeline remains completely filled during operation.


Step 4: Analyze the Signal Amplitude


Many vortex flow meter transmitters provide access to vortex signal amplitude or signal-to-noise ratio readings.


Observe how the signal changes as the flow rate decreases:
 

  • Signal amplitude decreases along with flow rate: The problem may be related to transmitter settings, signal filtering, or insufficient signal detection sensitivity.

  • Signal amplitude remains unchanged or suddenly drops to zero: The flow rate may have fallen below the meter's measurable range, or the signal chain may have developed a fault.


This step helps distinguish between configuration-related problems, insufficient flow velocity, and potential hardware or wiring issues.


4. Quick Troubleshooting Checklist

 
Inspection Item Recommended Check       Priority
Operating point and minimum flow limit             Ensure the minimum operating velocity is above the meter's specified lower limit             High
Low-flow cutoff       Evaluate whether 0.5%–1% FS is suitable instead of the default 5% setting       High
Full-pipe conditions and liquid carryover       Ensure liquid pipelines remain full and gas streams are free of liquid droplets       High
Signal amplitude       Verify that signal amplitude changes with flow rate under low-flow conditions       High
Straight pipe length and alignment       Typically 10D–15D upstream and 5D downstream       Medium
Grounding and shielding       Follow dedicated grounding and single-end shield grounding requirements       Medium


Conclusion


When a vortex flow meter stops displaying readings at low flow rates, replacing the instrument immediately is not always the right solution.


The first step is to verify whether the actual flow velocity falls within the meter's measurable range. Next, check the low-flow cutoff, filtering, and signal gain settings. Finally, inspect the pipeline installation, fluid conditions, and signal transmission chain.


If the operating flow rate is consistently below the meter's minimum measurable limit, adjusting the transmitter alone will not solve the problem. Selecting a properly sized flow meter or a more suitable measurement technology is often the better long-term solution.


Need help troubleshooting a vortex flow meter for your application? Contact Aister Instrument with your pipe diameter, fluid type, operating flow range, and process conditions. Our technical team can help evaluate the measurement range and recommend a suitable flow meter.

Share To:


Get a Quotation
Please fill out the following form to provide more details about your requirements, contacts, and desired products. We will promptly contact you for further confirmation.
English