ATLD Flange Connected Electromagnetic Flow Meter from China Manufacturer

Introduction Features Specifications Model Selection Application Installation

Introduction

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

The main advantages of using electromagnetic flow meter is that it is with no moving parts, no pressure loss and require very less maintenance.
Flange type magnetic flow meter can be made large size range from DN3-DN3000mm and with bi-directional flow measurement. Aister's electromagnetic flow meters are with built-in self-diagnosis function and support data record / bluetooth function and various kinds of output signals.

Compared with other liquid type flow meter, the limitations of magnetic flow meter is that it can only be used for conductive liquid.Regarding non or low conductive liquid such as petroleum products, organic solvents can not be used. Electromagnetic flow meter will be affected if there's strong magnetic filed in the surrounding environment.

Features

1.The total amount of forward, reverse and difference can be recorded；

2.The minimum conductivity of the liquid to be measured is ≥20μs/cm.

3.Current speed range：0.1 --- 15m/s ，current speed resolution：0.5mm/s;

4.AC high-frequency switching power ，range of voltage：85VAC --- 250VAC;

5.DC 24V switching power ，range of voltage：20VDC --- 36VDC；

6.Network function ：MODBUS, GPRS, PROFIBUS and HART communication protocol

7.LCD backlight display, online parameter modification, simple and convenient operation

8. The measurement accuracy is not affected by flow density, viscosity, temperature, pressure and conductivity

9. There are no moving parts in the measuring tube

010

10. Display language supports Chinese, English and Russian

Specifications

Performance	Technical parameter
Size	DN3-DN3000mm
Nominal Pressure	0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa...Max 42Mpa)
Accuracy	+/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner	PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode	SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type	Integral type, remote type, submersible type, ex-proof type
Medium Temperature	-20~+60 degC(Integral type)
Medium Temperature	Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature	-20~+60deg C
Ambient Humidity	5-100%RH(relative humidity)
Measuring Range	Max 15m/s
Conductivity	>5us/cm
Protection Class	IP65(Standard); IP68(Optional for remote type)
Process Connection	Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal	4-20mA/Pulse
Communication	RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply	AC220V (can be used for AC85-250V) DC24V (can be used for DC20-36V) DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption	<20W
Alarm	Upper Limit Alarm / Lower Limit Alarm
Self-diagnosis	Empty Pipe Alarm, Exciting Alarm
Explosion Proof	ATEX

Model Selection

01 Caliber

02 Nominal Pressure

03 Connection Mode

04 Liner Material

05 Electrode Material

06 Structure Type

07 Power

08 Output communication

09 Converter Figure

Application

Industrial process

Energy measurement

Environmental protection engineering

Transportation

Biotechnology

Scientific experiment

Marine meteorology

Rivers and lakes

Installation

Installation requirements

In order to let you can correct measuring, please be pay attention to the following requirements when choosing the line position
(1)the sensor not only installed in the straight pipe, but also can be installation the in level or tilted pipe, but the required of the center of two electrode attachment on the horizontal state
(2) the medium in the installation position should be full pipe flow, avoid not full pipe and gas attached to the electrode.
(3) For liquid-solid two-phase flow, it better choose the perpendicular installation, it make the liner material of the sensor attrition uniform, and prolong working life.
(4) when the flow meter installation position with not full medium, it can raise the end pipeline of the flowmeter, and make its full tube, forbidden in peak and outlet pipe installation flowmeter
(5) Modify piping installation method: when the medium velocity out of requires, it should choose a small caliber flow meter, and should use different caliber taper pipe or modify the sections of pipe, make its same caliber with sensor, but before and after straight pipe section at least requirement the before straight pipe section ≥10 DN, after straight pipe section≥5 DN (DN for pipe diameter)
(6) Before and after straight pipe section for the flowmeter ,before pipe section ≥10 DN, after pipe section≥5 DN

The instrument connection
★ If choose the signal of remote version connected, the cable must be use the customized special cables. And the cable shorter the better
★Excitation cable can choose Yz medium rubber cable ,and the length same as signal cable
★Signal cable must be strictly separate with others power supply,and can not laying in the same pipe inside.
★Signal cable and excitation cable should choose the shorter as soon as possible,and it can't coil together with the redundant cables,it should cut off the redundant cables,then rewelding the connector
★when cable mediate sensor interface, in port place to make U, it will prevent the rain penetration to the sensor.

Product Recommendation

ATMF In-line Thermal Mass Flowmeter

ATMF Flange Type Thermal Gas Mass Flow Meter is a gas flow meter that directly measures the mass of gas without temperature and pressure compensation, which represents the development trend of gas flow measurement.

Consult Now

Learn More

ATWG Gas Turbine Flowmeter

ATWG gas turbine flowmeter is mainly used for the flow measurement of natural gas, air, nitrogen and other medium fluids in industrial pipelines, and is almost unaffected by fluid density, pressure, temperature, viscosity and other parameters when measuring the volume flow under working conditions.

Consult Now

Learn More

ATLU Precession Vortex Flowmeter

Intelligent precession vortex flowmeter is a new type of gas flow meter developed by our company. The flowmeter integrates the function of flow, temperature and pressure detection, and can automatically compensate the temperature, pressure and compression factor.

Consult Now

Learn More

LUGB Flange Connected Vortex Flow Meter

Vortex flowmeter is a volume flowmeter that measures the volume flow of gas, steam or liquid, the volume flow of the standard condition or the mass flow according to the Karman vortex principle. It is mainly used for the flow measurement of industrial pipeline medium fluids, such as gas, liquid, steam and other media.

Consult Now

Learn More