Low Cost Electromagnetic Flowmeter 4-20mA Output Digital Magnetic Water Flow Meter Price

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter as a widely used precision instrument products, whether it is the purchase, installation and commissioning and use process need to spend a lot of energy, then, the use of electromagnetic flowmeter should pay attention to what problems?

For the pipeline supporting the electromagnetic flowmeter, the factors affecting the accuracy of the plug-in electromagnetic flowmeter are mainly the length of the straight pipe section and the inner diameter of the pipeline:

Selecting the appropriate installation point for an electromagnetic flowmeter is crucial for accurate and reliable measurements. Here are some considerations and guidelines to help you choose the right measuring installation point:

Electromagnetic flowmeter is a kind of induction instrument which measures the volume flow of conductive medium in tube according to Faraday’s law of electromagnetic induction. The electromagnetic flowmeter adds a magnetic field on both sides of the pipeline, and the measured medium flows through the pipeline to cut the magnetic force line, generating an induced potential on the two detection electrodes, and its size is proportional to the speed of fluid movement.

Electromagnetic flow meters, like any complex instrumentation, require effective fault diagnosis methods to ensure their optimal performance and reliability. One common approach to diagnosing issues with electromagnetic flow meters involves the analysis of the sensor signals. Any deviation from the expected output can be indicative of potential problems within the system. Advanced diagnostic algorithms can be employed to detect abnormalities in the induced voltage or electromagnetic field, allowing for the identification of faults such as sensor drift, signal noise, or electrode fouling.

Electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including the volume flow of acid, alkali, salt and other highly corrosive liquids.

Intelligent electromagnetic flowmeter measurement accuracy is high, stable performance, is a very common product in the flow meter, widely used in petroleum, chemical, food and other industries, especially water resources system, almost everywhere can see the figure of intelligent electromagnetic flowmeter, but the measured medium in these occasions is a single liquid, then with intelligent electromagnetic flowmeter can measure the mixture, Is a lot of owners are very want to know, I hope that today through this article to answer everyone’s doubts.

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

Electromagnetic flowmeters can measure mud. The electromagnetic flowmeter utilizes the principle of Faraday’s law of electromagnetic induction. It calculates the flow rate by measuring the induced electromotive force generated when a conductive liquid flows in a magnetic field. It has the advantages of high precision, no mechanical wear, and bidirectional measurement. Mud, as a conductive liquid containing a large amount of solid particles, although it has high requirements for measuring equipment, electromagnetic flowmeters, due to their unique measurement principles and superior performance, have become the ideal choice for measuring mud flow.

Electromagnetic flowmeter for our life has a great positive significance, for large pipe diameter occasions, the insertion electromagnetic flowmeter has obvious advantages, then about the insertion electromagnetic flowmeter you do not fully understand?

The installation direction of the electromagnetic flowmeter is not particularly strict requirements, generally horizontal, vertical or inclined can be unlimited. However, it must be reminded that in order to ensure that the pipeline is full of the measured medium, that is, the “full tube” state, it is recommended to install vertically, flow from bottom to bottom, especially for liquid-solid two-phase fluids, it must be installed vertically.

Electromagnetic flowmeter is composed of electromagnetic flow sensor and electromagnetic flow converter. The main components are measuring tube, electrode, excitation coil, iron core and yoke, housing. The measuring tube of the sensor is a short non-magnetic alloy tube lined with insulating material.

The choice of water flow meter is a comprehensive consideration process, involving many aspects of factors. Here is a guide to tap water flow meter selection to help you choose the most suitable solution:

The role of electromagnetic flow meter grounding in actual installation. Compared with other flowmeter products, electromagnetic flowmeter has high precision, reliable performance, stable work and excellent anti-interference ability. However, as a precision instrument, in order to meet these high requirements, it is necessary to have strict installation requirements, this article will introduce the electromagnetic flowmeter grounding wire that is often not paid attention to when installing.

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

One key advantage of electromagnetic flow meters is their versatility in handling various fluid types and conditions. Since they rely on the conductivity of the fluid rather than its physical properties, these meters are suitable for a wide range of applications, from clean water to corrosive chemicals. Additionally, they exhibit minimal pressure loss, making them an energy-efficient choice for flow measurement systems.

Electromagnetic flowmeter selection principle:

In the energy sector, particularly in power generation plants, electromagnetic flowmeters play a critical role in measuring cooling water flow. The accuracy and stability of these flowmeters help power plants maintain optimal operating conditions and monitor the efficiency of their cooling systems. Additionally, electromagnetic flowmeters are used in the oil and gas industry for measuring the flow of hydrocarbons, providing crucial data for production and transportation processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm

Battery-powered electromagnetic flowmeter is a metering instrument designed for water supply enterprises, which can optimize water use and ensure accurate water measurement.

Sewage flowmeter is an induction meter used to measure the volume flow of conductive medium in pipes.

Calibration checks are another essential component of fault diagnosis for electromagnetic flow meters. Regular calibration against known standards ensures that the meter’s measurements remain accurate over time. Any deviation from the expected calibration values may indicate sensor degradation, electronic component failure, or other issues that require attention.

electromagnetic flowmeters have emerged as indispensable tools for industries that demand accurate and reliable flow measurements. Their advanced technology, coupled with the ability to operate in diverse environments and handle various conductive liquids, positions them as a preferred choice in applications ranging from water management to chemical processing. As technology continues to evolve, electromagnetic flowmeters are likely to witness further advancements, contributing to increased efficiency and precision in liquid flow measurement across different sectors.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Usually there is more or less a mixture in the fluid in the measurement of some occasions. In general, in the presence of a small bubbling flow of oil and gas bubbles, it is still able to work normally, but the measurement is a fusion of the volume of oil bubbles, if the proportion of oil and gas rises to have caused a projectile flow, then the electrode may be covered by gas, resulting in the circuit is disconnected, the output shake is more likely to be directly damaged.

The grounding of the electromagnetic flowmeter is equipped with a grounding ring, and then the grounding ring is connected to the pipeline. If it’s lined, you need a third electrode to ground it.

The wastewater electromagnetic flowmeter is a device with a simple structure and relatively high sensitivity. However, since the accuracy of the wastewater electromagnetic flowmeter has been marked before leaving the factory, it is very likely to be affected by the surrounding environment during the operation process, and problems may occur. So, what should everyone pay attention to during the stage of using the wastewater electromagnetic flowmeter?

Electromagnetic flowmeters (usually referring to electromagnetic flowmeters, as electromagnetic itself is not directly used for flow measurement) can be installed on PE (polyethylene) pipes, but the following points should be noted to ensure their normal operation and measurement accuracy:

Advantages and disadvantages of electromagnetic flowmeter

What are the advantages of electromagnetic flowmeter measurement for sewage measurement? The plug-in electromagnetic flowmeter is composed of two parts: flow sensor and transmitter.