Remote Type Magnetic Flowmeter Caudalimetro DN100 8 Inch RS485 Digital

Electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including the volume flow of acid, alkali, salt and other highly corrosive liquids.

The shortage of water resources and the impact of sewage on the environment are the two major problems facing the solution of water resources. In the process of solving these problems, the flowmeter has a role that cannot be ignored. Choosing a good sewage flowmeter plays a crucial role in solving the problem.

High voltage electromagnetic flowmeters are commonly used in applications where the measurement of electrically conductive fluids is required. These flowmeters operate based on Faraday’s law of electromagnetic induction and are suitable for a variety of industrial processes. Here are some key application characteristics of high voltage electromagnetic flowmeters:

The sewage flowmeter has a wide range of applications and is favored by the owner, but the application performance of the sewage flowmeter has a great relationship with the installation on site. Aister makes the following requirements for the installation points of the sewage flowmeter:

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, are widely used for measuring the flow rate of conductive liquids in various industries. Several factors can influence the accuracy of electromagnetic flowmeters. Understanding and addressing these factors are essential to ensure precise and reliable flow measurements. Here are some key factors that can affect the accuracy of electromagnetic flowmeters:

Electromagnetic flowmeter grounding problem

Electromagnetic flowmeter is composed of two parts: sensor and converter. It is based on Faraday’s law of electromagnetic induction work, used to measure the conductivity of more than 20μS/cm conductive liquid volume flow, electromagnetic flowmeter is a measurement of conductive medium volume flow induction instrument.

Electromagnetic flow meters, like any complex instrumentation, require effective fault diagnosis methods to ensure their optimal performance and reliability. One common approach to diagnosing issues with electromagnetic flow meters involves the analysis of the sensor signals. Any deviation from the expected output can be indicative of potential problems within the system. Advanced diagnostic algorithms can be employed to detect abnormalities in the induced voltage or electromagnetic field, allowing for the identification of faults such as sensor drift, signal noise, or electrode fouling.

The measurement principle of the electromagnetic flowmeter is Faraday’s law of electromagnetic induction. It is an instrument that measures the flow of conductive fluids based on the induced electromotive force when the conductive fluid passes through an external magnetic field.

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Another important requirement of the electromagnetic flowmeter: how to accurately select the lining material, the lining material of the electromagnetic flowmeter should be selected according to the erosion, wear and temperature of the measured medium.

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

In the electromagnetic flowmeter installation and debugging stage there will be some failures, below, we will understand the specific causes of the failure at this stage and their elimination methods.

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

Another important requirement of the electromagnetic flowmeter: how to accurately select the lining material, the lining material of the electromagnetic flowmeter should be selected according to the erosion, wear and temperature of the measured medium.

With the speeding up of urbanization process in our country, environmental pollution is increasingly serious. Because in sewage treatment, it is necessary to analyze and control the discharged sewage, additives, sludge, etc., so the flow measurement is very important. Among the many flowmeter products used for sewage measurement, electromagnetic flowmeter measurement accuracy is higher.

The intelligent electromagnetic flowmeter is mainly used to measure the volume flow of conductive liquids and slurries in closed pipelines, including strongly corrosive liquids such as acids, alkalis and salts. Electromagnetic flowmeters are widely used in industries such as petroleum, chemical engineering, metallurgy, textile, food, pharmaceuticals, and papermaking, as well as in fields like environmental protection, municipal management, and water conservancy construction.

The installation of the electromagnetic flowmeter depends on the requirements of the customer’s working conditions, and then select the type, and install it according to the instructions or the guidance of the flowmeter manufacturer’s staff. The following points need to be noted when installing the electromagnetic flowmeter:

We have introduced a lot of relevant information about electromagnetic flowmeters before, and today we mainly introduce several typical installation errors to help you avoid these problems.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Selection of lining materials for electromagnetic flowmeter

Installing electromagnetic flowmeters correctly is essential for ensuring accurate and reliable flow measurement. Here are some precautions to consider when installing electromagnetic flowmeters:

Pipe diameter and pipe vibration

The pipe diameter range of some types of flowmeters is not very wide. Therefore, if it is too large or too small, it will limit the selection of flowmeter varieties. To measure low or high flow rates, a flowmeter pipe diameter different from the pipe diameter size can be selected.

What are the requirements for the installation environment of the electromagnetic flow meter?

Intelligent electromagnetic flowmeter measurement accuracy is high, stable performance, is a very common product in the flow meter, widely used in petroleum, chemical, food and other industries, especially water resources system, almost everywhere can see the figure of intelligent electromagnetic flowmeter, but the measured medium in these occasions is a single liquid, then with intelligent electromagnetic flowmeter can measure the mixture, Is a lot of owners are very want to know, I hope that today through this article to answer everyone’s doubts.

The application of flowmeter in food processing is very extensive, mainly reflected in the following aspects:

Notes for electromagnetic flowmeter selection:

electromagnetic flowmeters have a wide range of applications across diverse industries, addressing the need for accurate and efficient fluid flow measurement in fields as varied as water management, industrial processes, energy production, environmental monitoring, and HVAC systems. Their adaptability and reliability make them indispensable tools in ensuring precise fluid flow measurements for improved process control and operational performance.

Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)

What are the problems encountered when electromagnetic flowmeters are used in paper mills