Magnetic GPRS Flowmeter Acid Liquid Stainless Steel Electromagnetic RS485 Water Flow Meter

Electromagnetic flowmeter for our life has a great positive significance, for large pipe diameter occasions, the insertion electromagnetic flowmeter has obvious advantages, then about the insertion electromagnetic flowmeter you do not fully understand?

Intelligent electromagnetic flowmeter has a pivotal position in liquid measurement with high measurement accuracy and stable performance. It can be seen everywhere, today we mainly talk about the intelligent electromagnetic flowmeter in daily use, which parts – electrode related maintenance points:

What are the problems encountered when electromagnetic flowmeters are used in paper mills

The selection of circulating water flowmeter is a decision process involving many aspects, which needs to consider the characteristics of circulating water, measurement requirements, environmental conditions, economic costs and the performance characteristics of the flowmeter. Here is a comprehensive analysis and recommendations for the best options:

Improper selection and installation of split-type intelligent electromagnetic flowmeters can affect the accuracy of the flowmeter’s use and even damage the service life of the instrument. Today, the editor of Aister Instrument, a flowmeter manufacturer, will make the following discussion on the key points to note when installing split-type intelligent electromagnetic flowmeters.

The installation direction of the electromagnetic flowmeter is not particularly strict requirements, generally horizontal, vertical or inclined can be unlimited. However, it must be reminded that in order to ensure that the pipeline is full of the measured medium, that is, the “full tube” state, it is recommended to install vertically, flow from bottom to bottom, especially for liquid-solid two-phase fluids, it must be installed vertically. If the site only allows horizontal installation, it must be ensured that the two electrodes are in the same horizontal plane, and the axis of the electrode must be approximately horizontal, because the electrode at the bottom is easily covered by sediment, and the top electricity is easily wiped by the occasional bubble in the liquid, covering the electrode surface and making the output signal fluctuate. The following lists the matters that need attention in the installation of electromagnetic flowmeters:

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention:

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Due to various reasons, some large diameter flowmeters used online can not be tested off-line. It has become an urgent problem to study an online calibration method which is both scientific and effective and ADAPTS to the needs of the field. At present, there are three common methods for online calibration of electromagnetic flowmeters:

Electromagnetic flowmeters are used to measure the volume flow of industrial liquids and there are many media in industrial liquids, electromagnetic flowmeters are often used to measure the flow of conductive media.

The electrode is the main part of the electromagnetic flowmeter used to measure the liquid flow, therefore, the choice of normal electrode material is directly related to the accuracy of the measurement and the price of the electromagnetic flowmeter.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter is a kind of instrument to measure the flow of conductive fluid by using Faraday’s law of electromagnetic induction according to the electromotive force generated by the flow cutting magnetic field line. The common faults of electromagnetic flowmeter are: no display, inaccurate flow measurement, air traffic control alarm, system alarm, upper and lower limit alarm, etc.

Electromagnetic flowmeter has very good characteristics, can solve other flowmeter is not easy to apply problems, such as dirty flow, corrosion flow measurement, so the application of electromagnetic flowmeter is more and more extensive. To choose a suitable electromagnetic flowmeter for yourself, you must have an understanding of it.

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

Electromagnetic flowmeter has become one of the flow meters for measuring media in chemical enterprises. As long as the liquid has a certain conductivity, the electromagnetic flowmeter can be used to stop the flow measurement.

Precision and flow rate of electromagnetic flow meter

According to the composition of the sensor and the converter, the electromagnetic flowmeter can be divided into two types: separation type and one type. The separation type is to set the sensor and the converter independently, and the middle is connected with a cable, so the cable length is limited by the conductivity of the measured current body. One type is the sensor and converter as a whole set, so it is related to the fluid temperature and the ambient temperature, compared with the separation type, the applicable temperature range will be limited.

Compared with other flow measuring instruments, electromagnetic flowmeters have the following outstanding advantages

electromagnetic flowmeters are employed in HVAC (heating, ventilation, and air conditioning) systems to measure the flow of water or other fluids used for temperature control. The precision and reliability of these flowmeters ensure optimal performance of HVAC systems, leading to energy savings and improved comfort in various buildings and facilities.

Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)

In the field of industrial processes, electromagnetic flowmeters are extensively employed for measuring the flow of liquids such as chemicals, acids, and slurries. Their capability to handle corrosive fluids and resist wear makes them invaluable in industries like chemical manufacturing, pharmaceuticals, and food and beverage production. In these applications, electromagnetic flowmeters contribute to process optimization, ensuring precise control of fluid volumes and enhancing overall operational efficiency.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Electromagnetic flowmeters, also known as magmeters, are devices that measure the flow of electrically conductive fluids using the principles of electromagnetic induction. There are several types of electromagnetic flowmeters, each with its own characteristics and applications. Here are some common types:

A type electromagnetic flowmeter does not require a separate converter; The separation electromagnetic flowmeter type converter is installed near the sensor or the instrument room, the place to choose is larger, the environmental conditions are better than the sensor, and the protection level is IP65 or IP64 (dust and splash level).

The shell protection level of the ordinary electromagnetic flowmeter sensor is IP65 (the dustproof and anti-splash level stipulated by GB4208), and the requirements for the installation site are:

Electromagnetic flowmeter is a widely used flow meter, in the process of use will inevitably appear some failures, then how to check the cause of the failure and eliminate it, the next Aister to teach you several simple troubleshooting methods.

Another important requirement of the electromagnetic flowmeter: how to accurately select the lining material, the lining material of the electromagnetic flowmeter should be selected according to the erosion, wear and temperature of the measured medium.

The sewage flowmeter has a wide range of applications and is favored by the owner, but the application performance of the sewage flowmeter has a great relationship with the installation on site. Aister makes the following requirements for the installation points of the sewage flowmeter:

In the use of electromagnetic flowmeter measurement, we often have to consider how to deal with the problem of receiving no signal or signal is too weak, we should look for reasons from the following possible problems:

One of the defining features of electromagnetic flowmeters is their exceptional precision and accuracy in measuring fluid flow rates. The utilization of Faraday’s law of electromagnetic induction ensures that the induced voltage is directly proportional to the flow rate of the conductive liquid passing through the magnetic field. This inherent accuracy makes electromagnetic flowmeters a go-to choice in applications where precise measurements are critical, such as in pharmaceutical manufacturing, chemical processing, and water treatment.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm