Six advantages of electromagnetic flowmeter

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

The design of electromagnetic flow meters contributes to their robustness and long-term reliability. With no moving parts in contact with the fluid, they experience less wear and tear, resulting in extended operational life and reduced maintenance requirements. This makes them particularly suitable for applications where low-maintenance and high durability are crucial factors.

Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter for our life has a great positive significance, for large pipe diameter occasions, the insertion electromagnetic flowmeter has obvious advantages, then about the insertion electromagnetic flowmeter you do not fully understand?

Electromagnetic flowmeter in use, we need to pay attention to what? Today for you to do a simple description, I hope you pay attention to the following points about the maintenance of electromagnetic flowmeters:

One of the significant advantages of electromagnetic flowmeters is their high level of accuracy and reliability. With no moving parts in direct contact with the fluid, these devices experience minimal wear and tear, resulting in low maintenance requirements and increased longevity. Their versatility allows them to handle a broad spectrum of conductive liquids, from water and chemicals to slurries, making them suitable for a wide range of applications. Moreover, electromagnetic flowmeters are insensitive to changes in fluid properties, such as density, viscosity, and temperature, ensuring consistent and precise measurements across varying operating conditions.

Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

The shortage of water resources and the impact of sewage on the environment are the two major problems facing the solution of water resources. In the process of solving these problems, the flowmeter has a role that cannot be ignored. Choosing a good sewage flowmeter plays a crucial role in solving the problem.

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

Selecting the right electromagnetic flowmeter is crucial for accurate and reliable measurement of fluid flow in various industrial applications. One key consideration in the selection process is the type of fluid being measured. Electromagnetic flowmeters are suitable for a wide range of conductive fluids, such as water, acids, and slurries. Their performance can be affected by factors like conductivity and the presence of suspended solids, making it essential to choose a flowmeter that is compatible with the specific fluid characteristics.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s

The installation of the electromagnetic flowmeter depends on the requirements of the customer’s working conditions, and then select the type, and install it according to the instructions or the guidance of the flowmeter manufacturer’s staff. The following points need to be noted when installing the electromagnetic flowmeter:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The installation direction of the electromagnetic flowmeter is not particularly strict requirements, generally horizontal, vertical or inclined can be unlimited. However, it must be reminded that in order to ensure that the pipeline is full of the measured medium, that is, the “full tube” state, it is recommended to install vertically, flow from bottom to bottom, especially for liquid-solid two-phase fluids, it must be installed vertically. If the site only allows horizontal installation, it must be ensured that the two electrodes are in the same horizontal plane, and the axis of the electrode must be approximately horizontal, because the electrode at the bottom is easily covered by sediment, and the top electricity is easily wiped by the occasional bubble in the liquid, covering the electrode surface and making the output signal fluctuate. The following lists the matters that need attention in the installation of electromagnetic flowmeters:

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The versatility of electromagnetic flowmeters is a testament to their robust performance across a wide range of conductive liquids. Whether dealing with water, acids, bases, or slurries, these flowmeters maintain their accuracy and reliability. This adaptability is particularly valuable in industries with varying fluid compositions, allowing for a single flowmeter type to be employed in diverse applications without sacrificing performance.

Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

In order to prevent water resources from being polluted, improve living conditions and protect scarce water resources, most cities have established drinking water projects and sewage treatment plants. In the process of sewage treatment and discharge, the measurement of sewage flowmeter is an important problem. In the process of sewage metering, the selection of sewage flowmeter is very important.

Dealing with a weak signal issue in an intelligent electromagnetic flowmeter is crucial to ensure accurate and reliable flow measurements. Weak signals can be caused by various factors, and addressing them requires a systematic troubleshooting approach. Here are some steps to help you diagnose and resolve the weak signal phenomenon:

In the use of electromagnetic flowmeter measurement, we often have to consider how to deal with the problem of receiving no signal or signal is too weak, we should look for reasons from the following possible problems:

The working principle of electromagnetic flow meter:

Electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including the volume flow of acid, alkali, salt and other highly corrosive liquids.

Electromagnetic flowmeter is widely used in the industrial field, in order to make the electromagnetic flowmeter work stable and reliable, accurate measurement, installation needs to be installed in accordance with the correct method.

With the continuous acceleration of industrialization, the problem of environmental pollution is becoming more and more serious, and the call of society for sustainable development is getting higher and higher, so the control of pollution is more urgent.

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Basic fault treatment of intelligent sewage electromagnetic flowmeter:

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Notes for electromagnetic flowmeter selection:

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention:

The use of electromagnetic flowmeters is very wide, and this measuring instrument is used in many industries. Electromagnetic flowmeter is different from the general flowmeter, it follows the principle of electromagnetic induction, can measure the flow of liquid in the pipeline and its velocity.

Proper installation of electromagnetic flowmeters is crucial to ensure accurate and reliable measurement of fluid flow in various industrial applications. The first step in the installation process involves selecting an appropriate location for the flowmeter. It is essential to place the flowmeter in a section of the piping system where the flow profile is stable, avoiding areas with turbulence, elbows, or other disturbances that may affect the accuracy of measurements. Additionally, the installation site should provide easy access for maintenance and calibration activities.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

The sewage flowmeter has a wide range of applications and is favored by the owner, but the application performance of the sewage flowmeter has a great relationship with the installation on site. Aister makes the following requirements for the installation points of the sewage flowmeter: