Good Accuracy DN80 RS485 Integrated 316L Stainless Steel Sanitary Clamp on Magnetic Milk Flowmeter

The grounding of the electromagnetic flowmeter is equipped with a grounding ring, and then the grounding ring is connected to the pipeline. If it’s lined, you need a third electrode to ground it.

Today we bring you an introduction to the cleaning method of the plug-in electromagnetic flowmeter.

Electromagnetic flowmeter has very good characteristics, can solve other flowmeter is not easy to apply problems, such as dirty flow, corrosion flow measurement, so the application of electromagnetic flowmeter is more and more extensive. To choose a suitable electromagnetic flowmeter for yourself, you must have an understanding of it.

The requirements of the straight tube section of the electromagnetic flowmeter are very important to ensure the accuracy and stability of the measurement results. The following is a detailed analysis of the requirements of the straight pipe section before and after the electromagnetic flowmeter:

Electromagnetic flowmeter is a widely used flow meter, in the process of use will inevitably appear some failures, then how to check the cause of the failure and eliminate it, the next Aister to teach you several simple troubleshooting methods.

Electromagnetic flowmeter in the use process will produce some faults affect the normal work of the instrument, how to find the cause behind the fault is a very important work, we need to identify through a variety of different types of detection methods, in general, we for electromagnetic flowmeter routine testing, usually including electrode contact resistance, electrode polarization voltage, Signal cable interference, the determination of whether there is a grounding potential and the flow of stray current in the pipeline five aspects, these five aspects can be carried out separately, in fact, but also interrelated, any change in the factor may cause other changes, this reminds everyone in the detection of special attention:

The installation of the electromagnetic flowmeter depends on the requirements of the customer’s working conditions, and then select the type, and install it according to the instructions or the guidance of the flowmeter manufacturer’s staff. The following points need to be noted when installing the electromagnetic flowmeter:

The role of electromagnetic flow meter grounding in actual installation. Compared with other flowmeter products, electromagnetic flowmeter has high precision, reliable performance, stable work and excellent anti-interference ability. However, as a precision instrument, in order to meet these high requirements, it is necessary to have strict installation requirements, this article will introduce the electromagnetic flowmeter grounding wire that is often not paid attention to when installing.

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

The transducer in the split electromagnetic flowmeter can form a body or separate type with the sensor, the integrated electromagnetic flowmeter is the integrated electromagnetic flowmeter, the split type becomes the split electromagnetic flowmeter, the flowmeter is a two-way measurement system, and the three integrators are installed: the forward total, the reverse total and the difference total; Can be displayed. And has a variety of outputs: current, pulse, digital communication, HART, taking split electromagnetic flowmeter as an example to introduce what problems should be paid attention to when installing:

The shortage of water resources and the impact of sewage on the environment are the two major problems facing the solution of water resources. In the process of solving these problems, the flowmeter has a role that cannot be ignored. Choosing a good sewage flowmeter plays a crucial role in solving the problem.

One of the defining features of electromagnetic flowmeters is their exceptional precision and accuracy in measuring fluid flow rates. The utilization of Faraday’s law of electromagnetic induction ensures that the induced voltage is directly proportional to the flow rate of the conductive liquid passing through the magnetic field. This inherent accuracy makes electromagnetic flowmeters a go-to choice in applications where precise measurements are critical, such as in pharmaceutical manufacturing, chemical processing, and water treatment.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

The electromagnetic flow meter consists of a non-conductive pipe lined with a conductive material, typically made of metal. The meter contains coils or electrodes positioned opposite each other on the pipe’s inner walls. A magnetic field is then generated by passing a current through these coils, creating a measurable voltage across the fluid. The induced voltage, or EMF, is directly proportional to the fluid’s velocity, allowing the flow meter to accurately determine the flow rate. Importantly, this principle remains effective regardless of the fluid’s conductivity, making electromagnetic flow meters suitable for a wide range of applications, including water, wastewater, and various industrial processes.

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter is a kind of instrument to measure the flow of conductive fluid by using Faraday’s law of electromagnetic induction according to the electromotive force generated by the flow cutting magnetic field line. The common faults of electromagnetic flowmeter are: no display, inaccurate flow measurement, air traffic control alarm, system alarm, upper and lower limit alarm, etc.

In addition to signal analysis, real-time monitoring is a crucial aspect of fault diagnosis for electromagnetic flow meters. Continuous assessment of key parameters, such as fluid conductivity and temperature, can help detect anomalies that may impact meter accuracy. For instance, sudden changes in conductivity might signal issues like fluid contamination or changes in fluid composition, prompting the need for further investigation.

According to the composition of the sensor and the converter, the electromagnetic flowmeter can be divided into two types: separation type and one type. The separation type is to set the sensor and the converter independently, and the middle is connected with a cable, so the cable length is limited by the conductivity of the measured current body. One type is the sensor and converter as a whole set, so it is related to the fluid temperature and the ambient temperature, compared with the separation type, the applicable temperature range will be limited.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s
Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Electromagnetic flowmeter is a kind of induction meter to measure the volume flow of conductive medium, which can be used to measure the volume flow of strong corrosive liquid such as strong acid and alkali and uniform liquid-solid two-phase suspended liquid such as mud, pulp, pulp, etc.

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the good use of electromagnetic flowmeter. What kind of electromagnetic flowmeter should be selected should be determined according to the physical and chemical properties of the measured body medium, so that the diameter of the electromagnetic flowmeter, flow range, lining material, electrode material and output current, etc., can adapt to the nature and flow requirements of the measured body.

Electromagnetic flowmeter as a commonly used flow measurement instrument, the choice of its material is also an important factor. Because in the electromagnetic flowmeter, the part in contact with the medium is only the electrode and the inside of the measuring tube, it is necessary to select the correct electrode and lining material according to the characteristics of different media.

Electromagnetic flowmeters can achieve remote communication through various digital communication protocols. These protocols allow flowmeter data to be transmitted to remote monitoring systems, control rooms, or other devices for real-time monitoring, analysis, and control. Some common digital communication protocols used for remote communication with electromagnetic flowmeters include:

In the use of electromagnetic flowmeter measurement, we often have to consider how to deal with the problem of receiving no signal or signal is too weak, we should look for reasons from the following possible problems:

In the use of electromagnetic flowmeter measurement, we often have to consider how to deal with the problem of receiving no signal or signal is too weak, we should look for reasons from the following possible problems:

Electromagnetic flow meter is one of the most popular flow meters. Flange type electromagnetic flow meter has been used for more than 50 years worldwide. It is widely used for all conductive liquids in every industry, such as water, acid, alkali, milk, slurry etc.

Electromagnetic flow meters offer several advantages, making them a popular choice in various industrial applications. Here are some of the key advantages of electromagnetic flow meters:

High voltage electromagnetic flowmeters are commonly used in applications where the measurement of electrically conductive fluids is required. These flowmeters operate based on Faraday’s law of electromagnetic induction and are suitable for a variety of industrial processes. Here are some key application characteristics of high voltage electromagnetic flowmeters:

Selection of lining materials for electromagnetic flowmeter