Different occasions should choose different electromagnetic flowmeters

The electromagnetic flowmeter uses the principle of Faraday’s electromagnetic induction law to calculate the flow rate by measuring the induced potential generated by the conductive liquid flowing in the magnetic field, and has the advantages of high precision, no mechanical wear, and two-way measurement.

Four physical cleaning methods of electromagnetic flowmeter electrode

Electromagnetic flowmeter, with high precision, long life characteristics, in chemical industry, environmental protection, metallurgy and other fields and industries have been applied. However, in the process of use, due to the influence of many factors, it is easy to cause the inaccurate measurement results of the electromagnetic flowmeter. So what are the reasons for the error of the electromagnetic flowmeter?

The shortage of water resources and the impact of sewage on the environment are the two major problems facing the solution of water resources. In the process of solving these problems, the flowmeter has a role that cannot be ignored. Choosing a good sewage flowmeter plays a crucial role in solving the problem.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeter, with high precision, long life characteristics, in chemical industry, environmental protection, metallurgy and other fields and industries have been applied.

Sewage flowmeter is an induction meter used to measure the volume flow of conductive medium in pipes.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

The measuring principle of intelligent electromagnetic flowmeter is Faraday’s law of electromagnetic induction, which measures the flow of conductive fluid according to the electromotive force induced by the conductive fluid through the external magnetic field. The main components of the sensor are: measuring tube, electrode, excitation coil, iron core and yoke shell.

As a measuring device with simple structure, sensitive response and not affected by physical properties such as temperature and viscosity of the measured medium, electromagnetic flowmeter has been widely used in the water supply industry, and has obtained good results.

Electromagnetic flowmeter has become one of the flow meters for measuring media in chemical enterprises. As long as the liquid has a certain conductivity, the electromagnetic flowmeter can be used to stop the flow measurement.

1. The sensor structure of the electromagnetic flowmeter is simple, and there are no moving parts in the measuring tube, nor any throttling parts that hinder the flow of fluid. So when the fluid through the flow timing will not cause any additional pressure loss, electromagnetic flowmeter is a very low energy consumption flow meter.

Electromagnetic flowmeters, also known as magmeters or magnetic flowmeters, typically generate electrical output signals proportional to the flow rate of a conductive fluid passing through a pipe. The most common output signals from electromagnetic flowmeters include:

The correct selection of electromagnetic flowmeter is the prerequisite to ensure the good use of electromagnetic flowmeter. What kind of electromagnetic flowmeter should be selected should be determined according to the physical and chemical properties of the measured body medium, so that the diameter of the electromagnetic flowmeter, flow range, lining material, electrode material and output current, etc., can adapt to the nature and flow requirements of the measured body.

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

We have introduced a lot of relevant information about electromagnetic flowmeters before, and today we mainly introduce several typical installation errors to help you avoid these problems.

Intelligent electromagnetic flowmeter measurement accuracy is high, stable performance, is a very common product in the flow meter, widely used in petroleum, chemical, food and other industries, especially water resources system, almost everywhere can see the figure of intelligent electromagnetic flowmeter, but the measured medium in these occasions is a single liquid, then with intelligent electromagnetic flowmeter can measure the mixture, Aister meter is your answer.

Electromagnetic flowmeter is a speed meter to measure the volume flow of conductive media. While carrying out on-site monitoring and display, it can output standard current signals for recording, adjustment and control, realizing automatic control of detection, and realizing long-distance transmission of signals. It can be widely used in water, chemical, coal, environmental protection, textile, metallurgy, paper and other industries in the flow measurement of conductive liquid. The structure of the instrument has one type and one type.

Performance Technical parameter
Size DN3-DN3000mm
Nominal Pressure 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type Integral type, remote type, submersible type, ex-proof type
Medium Temperature -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature -20~+60deg C
Ambient Humidity 5-100%RH(relative humidity)
Measuring Range Max 15m/s
Conductivity >5us/cm
Protection Class IP65(Standard); IP68(Optional for remote type)
Process Connection Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal 4-20mA/Pulse
Communication RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption <20W Alarm Upper Limit Alarm / Lower Limit Alarm Self-diagnosis Empty Pipe Alarm, Exciting Alarm Explosion Proof ATEX

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard), 0.3% or 0.2% (Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Output Signal: 4-20mA/Pulse

Electromagnetic flowmeters, commonly known as magmeters, are a sophisticated and versatile type of flow measurement device widely used in industrial applications. Unlike traditional mechanical flow meters, electromagnetic flowmeters operate on the principle of electromagnetic induction to provide highly accurate and reliable measurements of liquid flow. The technology behind these devices makes them suitable for a diverse range of industries where precise flow measurement is crucial for various processes.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type

In the electromagnetic flowmeter installation and debugging stage there will be some failures, below, we will understand the specific causes of the failure at this stage and their elimination methods.

The installation distance between an electromagnetic flowmeter and a control valve, especially a rear valve, is a critical factor that can impact the accuracy and reliability of flow measurements. Here are some general guidelines to help determine the appropriate installation distance:

In industry, electromagnetic flowmeter is a kind of flow meter with a wide range of uses. Electromagnetic flowmeter is divided into: one type, sub-type, insert type. Different occasions need to choose different electromagnetic flowmeters to ensure the measurement results.

Suitability of electromagnetic flowmeters in chlor-alkali measurement chlor-alkali occupation measurement of brine and caustic soda, both of which have the same characteristics:

High voltage electromagnetic flowmeters are commonly used in applications where the measurement of electrically conductive fluids is required. These flowmeters operate based on Faraday’s law of electromagnetic induction and are suitable for a variety of industrial processes. Here are some key application characteristics of high voltage electromagnetic flowmeters:

When using electromagnetic flowmeters in the field, it’s important to perform regular checks and maintenance to ensure accurate and reliable flow measurements. Here are some key parameters to check and consider in the field for electromagnetic flowmeter use:

Electromagnetic flowmeters, also known as magmeters, are widely used in various industries for measuring the flow rate of conductive fluids. They operate based on Faraday’s law of electromagnetic induction, where a voltage is induced in a conductor (the fluid) as it moves through a magnetic field. These flowmeters are favored for their accuracy, reliability, and suitability for a wide range of applications. Here are different categories of electromagnetic flowmeters and their fields of application:

Fixed the electromagnetic flowmeter for periodic visual inspection, check the environment around the instrument, clean dirt, ensure that no water and other substances, check whether the wiring is good, check whether the electromagnetic flowmeter near the new installation of strong electromagnetic field equipment or a new wire across the instrument.

The installation direction of the electromagnetic flowmeter is not particularly strict requirements, generally horizontal, vertical or inclined can be unlimited. However, it must be reminded that in order to ensure that the pipeline is full of the measured medium, that is, the “full tube” state, it is recommended to install vertically, flow from bottom to bottom, especially for liquid-solid two-phase fluids, it must be installed vertically.