How to select the electromagnetic flowmeter protection level

The electromagnetic flowmeter uses the principle of Faraday’s electromagnetic induction law to calculate the flow rate by measuring the induced potential generated by the conductive liquid flowing in the magnetic field, and has the advantages of high precision, no mechanical wear, and two-way measurement.

Electromagnetic flow meters operate based on a fundamental principle of electromagnetic induction, providing an accurate and reliable method for measuring the flow of conductive fluids. The working principle involves Faraday’s law of electromagnetic induction. As a conductive fluid flows through a pipe, it cuts across the magnetic field generated by coils or electrodes mounted on the flow meter. According to Faraday’s law, an electromotive force (EMF) is induced in the fluid perpendicular to both the magnetic field and the flow direction. The induced EMF is directly proportional to the flow velocity of the fluid.

In the metering industry, electromagnetic flowmeter is a basic metering tool, and its range of use is very wide. The emergence of electromagnetic flowmeters has made great contributions to many industries, and it occupies a very important position in these industries. Pay more attention when using the electromagnetic flowmeter, check it before use to see how accurate its measurement is. The calibration of electromagnetic flowmeter is mainly considered from the following aspects:

The installation direction of the electromagnetic flowmeter is not particularly strict requirements, generally horizontal, vertical or inclined can be unlimited. However, it must be reminded that in order to ensure that the pipeline is full of the measured medium, that is, the “full tube” state, it is recommended to install vertically, flow from bottom to bottom, especially for liquid-solid two-phase fluids, it must be installed vertically.

Intelligent electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including acid, alkali, salt and other highly corrosive liquids.

Electromagnetic flowmeters, also known as magmeters, are widely used in various industries for measuring the flow rate of conductive fluids. They operate based on Faraday’s law of electromagnetic induction, where a voltage is induced in a conductor (the fluid) as it moves through a magnetic field. These flowmeters are favored for their accuracy, reliability, and suitability for a wide range of applications. Here are different categories of electromagnetic flowmeters and their fields of application:

Electromagnetic flowmeter at work requires that the measured medium must be ground potential, generally through the pipeline or flange ground, if the process pipe connected to the sensor relative to the measured medium is insulated (plastic pipe or pipe with an insulating lining), you must choose a grounding ring or sensor with a grounding electrode, so that the measured medium in the ground potential, easy to be ignored in the actual design and installation.

The measuring accuracy and stability of the electromagnetic flowmeter is directly related to whether the electromagnetic flowmeter housing is grounded.

The measurement of sewage by electromagnetic flowmeter generally does not require daily maintenance, but when the measured medium is easy to adhere to or scale the inner wall of the electrode and the measuring tube, it is necessary to regularly clean the inner wall of the measuring tube and the electrode, and be careful not to damage the flowmeter lining and the electrode.

Non-full tube electromagnetic flowmeter is an advanced flow measuring instrument, especially suitable for measuring the flow of non-full tube or partially filled fluid, such as municipal rainwater, wastewater, sewage and so on. The following is a detailed introduction to the non-full tube electromagnetic flowmeter:

One of the defining features of electromagnetic flowmeters is their exceptional precision and accuracy in measuring fluid flow rates. The utilization of Faraday’s law of electromagnetic induction ensures that the induced voltage is directly proportional to the flow rate of the conductive liquid passing through the magnetic field. This inherent accuracy makes electromagnetic flowmeters a go-to choice in applications where precise measurements are critical, such as in pharmaceutical manufacturing, chemical processing, and water treatment.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm

Intelligent electromagnetic flowmeter measurement accuracy is high, stable performance, is a very common product in the flow meter, widely used in petroleum, chemical, food and other industries, especially water resources system, almost everywhere can see the figure of intelligent electromagnetic flowmeter, but the measured medium in these occasions is a single liquid, then with intelligent electromagnetic flowmeter can measure the mixture, Aister meter is your answer.

1. The sensor structure of the electromagnetic flowmeter is simple, and there are no moving parts in the measuring tube, nor any throttling parts that hinder the flow of fluid. So when the fluid through the flow timing will not cause any additional pressure loss, electromagnetic flowmeter is a very low energy consumption flow meter.

electromagnetic flowmeters have emerged as indispensable tools for industries that demand accurate and reliable flow measurements. Their advanced technology, coupled with the ability to operate in diverse environments and handle various conductive liquids, positions them as a preferred choice in applications ranging from water management to chemical processing. As technology continues to evolve, electromagnetic flowmeters are likely to witness further advancements, contributing to increased efficiency and precision in liquid flow measurement across different sectors.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa… Max 42Mpa)
Accuracy: +/-0.5%(Standard) +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s
Conductivity: >5us/cm
Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

Size: DN15mm-DN200mm
Nominal Pressure: 1.6Mpa
Accuracy: ±0.5%(Standard)
Liner: FEP, PFA
Output Signal: 4-20mA pulse frequency relay

Impurities in the medium flowing through electromagnetic flowmeters can have several effects on their performance and accuracy. While electromagnetic flowmeters are known for their versatility and ability to handle a variety of fluids, the presence of certain impurities may impact their operation. Here are some potential effects:

Electromagnetic flowmeter, with high precision, long life characteristics, in chemical industry, environmental protection, metallurgy and other fields and industries have been applied. However, in the process of use, due to the influence of many factors, it is easy to cause the inaccurate measurement results of the electromagnetic flowmeter. So what are the reasons for the error of the electromagnetic flowmeter?

The versatility of electromagnetic flowmeters is a testament to their robust performance across a wide range of conductive liquids. Whether dealing with water, acids, bases, or slurries, these flowmeters maintain their accuracy and reliability. This adaptability is particularly valuable in industries with varying fluid compositions, allowing for a single flowmeter type to be employed in diverse applications without sacrificing performance.

Protection Class: IP65(Standard); IP68(Optional for remote type)
Process Connection: Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal: 4-20mA/Pulse
Communication: RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply: AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)
Power Consumption: <20W Alarm: Upper Limit Alarm / Lower Limit Alarm Self-diagnosis: Empty Pipe Alarm, Exciting Alarm Explosion Proof: ATEX

Electromagnetic flowmeter, with high precision, long life characteristics, in chemical industry, environmental protection, metallurgy and other fields and industries have been applied.

Electromagnetic flowmeter as a commonly used flow measurement instrument, the choice of its material is also an important factor. Because in the electromagnetic flowmeter, the part in contact with the medium is only the electrode and the inside of the measuring tube, it is necessary to select the correct electrode and lining material according to the characteristics of different media.

Electromagnetic flowmeters are classified according to the assembly method of converters and sensors, with split type and one type. Split type electromagnetic flowmeter is relative to the integrated, its components are: measuring tube, electrode, excitation coil, iron core and yoke housing. Used to measure the volume flow of conductive liquid and slurry in closed pipes.

The transducer in the split electromagnetic flowmeter can form a body or separate type with the sensor, the integrated electromagnetic flowmeter is the integrated electromagnetic flowmeter, the split type becomes the split electromagnetic flowmeter, the flowmeter is a two-way measurement system, and the three integrators are installed: the forward total, the reverse total and the difference total; Can be displayed. And has a variety of outputs: current, pulse, digital communication, HART, taking split electromagnetic flowmeter as an example to introduce what problems should be paid attention to when installing:

electromagnetic flowmeters have a wide range of applications across diverse industries, addressing the need for accurate and efficient fluid flow measurement in fields as varied as water management, industrial processes, energy production, environmental monitoring, and HVAC systems. Their adaptability and reliability make them indispensable tools in ensuring precise fluid flow measurements for improved process control and operational performance.

Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range： Max 15m/s
Conductivity： >5us/cm
Protection Class： IP65(Standard); IP68(Optional for remote type)
Process Connection： Flange (Standard), Wafer, Thread, Tri-clamp etc (Optional)
Output Signal： 4-20mA/Pulse
Communication： RS485(Standard), HART(Optional),GPRS/GSM (Optional)
Power Supply： AC220V (can be used for AC85-250V)
DC24V (can be used for DC20-36V)
DC12V (optional), Battery Powered 3.6V (optional)

Measuring medium: Conductive liquid
Diameter range: DN3mm～DN3000mm
Accuracy: ± 0.5% of the indicated value, optional ± 0.3% or ± 0.2%
Measuring range (Flow rate): 0.01m/s～15m/s

Electromagnetic flowmeter, with high precision, long life characteristics, in chemical industry, environmental protection, metallurgy and other fields and industries have been applied. However, in the process of use, due to the influence of many factors, it is easy to cause the inaccurate measurement results of the electromagnetic flowmeter. So what are the reasons for the error of the electromagnetic flowmeter?

The scale of the water supply system itself is huge, and the environment in which it is located is complex and changeable, requiring the electromagnetic flowmeter to have strong stability and reliability, so in the actual use process, the matters needing attention should be clear.

Selecting the right electromagnetic flowmeter is crucial for accurate and reliable measurement of fluid flow in various industrial applications. One key consideration in the selection process is the type of fluid being measured. Electromagnetic flowmeters are suitable for a wide range of conductive fluids, such as water, acids, and slurries. Their performance can be affected by factors like conductivity and the presence of suspended solids, making it essential to choose a flowmeter that is compatible with the specific fluid characteristics.

Size: DN3-DN3000mm
Nominal Pressure: 0.6-1.6Mpa(2.5Mpa/4.0Mpa/6.4Mpa…Max 42Mpa)
Accuracy: +/-0.5%(Standard)     +/-0.3% or +/-0.2%(Optional)
Liner: PTFE, Neoprene, Hard Rubber, EPDM, FEP, Polyurethane, PFA
Electrode: SUS316L, Hastelloy B, Hastelloy C       Titanium, Tantalum, Platinium-iridium
Structure Type: Integral type, remote type, submersible type, ex-proof type
Medium Temperature: -20~+60 degC(Integral type)
Remote type ( Neoprene ,Hard Rubber ,Polyurethane ,EPDM) -10~+80degC
Remote type(PTFE/PFA/FEP) -10~+160degC
Ambient Temperature: -20~+60deg C
Ambient Humidity: 5-100%RH(relative humidity)
Measuring Range: Max 15m/s

Electromagnetic flowmeters are mainly used to measure the volume flow of conductive liquid and slurry in closed pipelines, including the volume flow of acid, alkali, salt and other highly corrosive liquids.

The design of electromagnetic flow meters contributes to their robustness and long-term reliability. With no moving parts in contact with the fluid, they experience less wear and tear, resulting in extended operational life and reduced maintenance requirements. This makes them particularly suitable for applications where low-maintenance and high durability are crucial factors.

Suitability of electromagnetic flowmeters in chlor-alkali measurement chlor-alkali occupation measurement of brine and caustic soda, both of which have the same characteristics: